Search results

Early Bay Forum

Help Support Early Bay Forum:

  1. Darren2030

    Weber 34 ict

    Yeh got the bus booked in next Friday on a rolling road mate want it running sweet with no problems…I am a bit pissed off eurocarb told me to look on his website for jet guidance thou!
  2. Darren2030

    Routing Fuel lines

    Nice one Karlos cheers mate
  3. Darren2030

    Routing Fuel lines

    Cheers Moseley yeh don’t think I’ll use any elbows anyway mate I reckon I’ll get a nice wide bend in the fuel line to the right hand carb to avoid stressing it too much and the left hand carb will come off the T piece but will obviously be shorter than the right side.
  4. Darren2030

    Routing Fuel lines

    Cheers mate didn’t think it would just wanted to be 100% before I started Chopin up expensive fuel line!
  5. Darren2030

    Weber 34 ict

    Thank you mate appreciated
  6. Darren2030

    Routing Fuel lines

    Hi Mike thanks appreciate your reply bud just wanted to make sure mate
  7. Darren2030

    Routing Fuel lines

    Hi fellas Sorry if this seems like a dumb question but do the fuel lines to each carburettor (34ict) have to be of similar lengths!? Was going to route a line from the mechanical pump to the regulator mounted on the left of the engine bay a T piece and then a smaller fuel line to the left carb...
  8. Darren2030

    Oil light came on. Help!

    Hi mate I also jetted to that spec and am now concerned that the Webers aren’t set up right! Believe it or not the person on the other end of the phone at eurocarb told me to look on his website for guidance on jetting them when I bought em!! Have you had any problems with yours bud? Gonna...
  9. Darren2030

    Weber 34 ict

    That’s great thank you mate I will pm you my email address and take a look at the guide, did you change you float levels at all or did you leave them as they came? I only ask cus my r/h carb leaked fuel from the bottom until I altered the float level!? Cheers Darren
  10. Darren2030

    Weber 34 ict

    Hi Could anyone plz advise me on the float level setting on these carbs I’ve read 8mm and 5.5mm etc which I think eurocarb set them at and also the correct fuel pressure they are supposed to be at is it 2.1? I’ve got a mechanical fuel pump and a sp 1641 engine, I’ve had them jetted 145 mains...
  11. Darren2030

    Charcoal filter

  12. Darren2030

    Charcoal filter

    Hiya I’ve Recently removed the solex single carb and replaced with twin 34 ict webers which is a big improvement I was just wondering if it’s ok to vent the oil breather to the charcoal canister I’ve got in the top right hand corner of the engine bay instead of one of the filters!? Or would it...
  13. Darren2030

    Your Early Bay Picture of the Day .....

    Night ferry to Holland couple years ago for a week in dunirell theme park highly recommended 🙌
  14. Darren2030

    Single port dual Webers

    Wanted Hi I’m after a single port dual Weber carb set up if any one has one 34icts preferably in good working condition for 1641 sp engine, cheers.
  15. Darren2030

    Carburettor gasket

    Yeh checked float height and needle and it’s as you said mate 20mm below the top have also noticed a small leak from one of the jets on the right hand side of the carb got to be honest think it’s had it’s day!
  16. Darren2030

    Carburettor gasket

    Hi fellas Put the carburettor back on today with new gaskets top and bottom and for some bizarre reason while the engine was running I could see the gasket on top of the carburettor starting to go from grey to slowly black as petrol was trying to get out, can’t seem to fathom this out then the...
  17. Darren2030

    Insurance - again

    Always used justkampers past 3-4 years never had a problem with em agreed value of 30k on our 70 westy
  18. Darren2030

    Carburettor gasket

    Hi Moseley I can see your point mate yes i ain’t no expert but I can’t seem to see any other place on the carburettor where it could be leaking from, I originally thought it was the main jet screw on the side and have replaced the fibre washer on that and that seems ok I’m gonna change the top...
  19. Darren2030

    Carburettor gasket

    Thanks mate yeh will do gonna get it sorted and back together at the weekend hopefully no more leaks 🤞 Thanks again fellas
  20. Darren2030

    Carburettor gasket

    Thanks for you reply’s fellas much appreciated and helpful as always I’ll fit them dry and make 100% sure everything is nice and clean, as I said earlier these other gaskets look a lot better and more like giving a much better seal! Thanks again
Top