Search results

Hi everyone- the muf bus now has a great new home! Thanks for your interest! Rob

Here is our 1968 early bay. We imported her from the Palm Desert, California, 5 years ago. This is an OG paint, 1 key bus- after looking at several busses in the UK we decided we wanted a van in her original paint and no nasty surprises under a shiny new coat of paint. As you would expect from a...

Now sold- thanks!

Hi all- I have for sale some KYB double loop shocks 420/ 265mm. These shocks are virtually brand new, covered around 1000miles. These shock give a lovely smooth and comfortable ride. £40- collection from Lingfield, Surrey preferred but could probably post at additional cost. Drop me an email...

Hi I've got a Web 218 in by bus with stock ratio rockers (2054 with 044 supermags) C/R 8.5:1 and it is fantastic, such a torquey cam with a nice spread of power to about 5500rpm- great for a bus in my opinion, maybe worth a look- I got mine from Jim at Stateside Tuning. I also had an Engle 110...

I think I have a good 205t fitted with a petronix elec ignition in my garage. Where are you?

Hi all, Still have these for sale for £40 if any one is interested, practically brand new- Collection from Edenbridge, Kent. I also have some US spec original headlights from my van, that I don't need now as I've swapped to Euro spec with side lights- open to offers on these! Cheers

Hi sharky, I went for the gaz GP coilovers on the front, 9" shocks with 150lb springs, although I haven't driven the van since fitting it is loads stiffer but the beauty of these is they are hight and damping adjustable and the spings can be easily and fairly cheaply swapped. I only have about...

KYB double loop shocks 420/ 265mm. These shocks are virtually brand new, covered around 1000miles. I have upgraded to Gaz coil overs because the tires were catching on the arch as the bus is quite low- didn't want to raise it up so have had to stiffen the front. These shock give a lovely smooth...

For sale- Front Beam to fit early bay (67/68) with early bolt pattern. The early bolt pattern is the same as the splitscreen and these beams are used to convert splits from king pin to ball joint. Includes trailing arm and spindles but no torsion leaves- would benefit from new ball joints...

Beam reduced, open to offers on tires

Happy New Year all, I still have all this stuff if its any use to anyone, could do with making some space so open to offers. I also have spindles and trailing arms for beam, would need new ball joints though! Many Thanks, Rob 07876705790

Hi I have one with a brand new rubber pipe too. I don't need it now cos I've fitted twin carbs! £45. Let me know if your interested

Hi, I have horseshoe plates on the rear of mine and I used shorter shocks on the back. There is a good guide to custom ride height shock sizing on the machine 7 website. With the horse shoe plates, I calculated the shocks I needed would be the same size as standard FRONT shocks. I used KYB GR2...

PMs Replied to!

Hi all, need to make some space in the garage to get my van in! Here goes; *185-14C 6Ply Commercial tyres (x2). Perfect for van with 14 Inch tyres. Came off the front of my van (In favour of Lower prfiles- still got a set on the back) They have less then 30 miles on (£45) *Falken ZE912...

Thanks for the info Araon, so basically i should look for this piece of tin without the dog house aperture and this will do the trick? Yes you are right, it is has had a 1500 single port beetle engine fitted by the PO, prob upgrade this next year. I'd assume this would make quite a big...

Hi everyone. My 68 has been running a little hot recently, after checking the mixture, tappet gaps, timing etc, I noticed the front piece of tinware (above the gear box) does not fit properly. After doing a search on here it looks likely I have type 1 tinware (also note many people extend...

On my RM 123 you can take the gas knob off under the door and then take the plate off behind the knob to reveal the lower vent and use the upper vent as you said. This is how i am going to run mine, the fridge will obviusly work better with colder air passing over the condensor coil but should...

Hi all, Yesterday I braved the cold weather and lowered the back of my '68 cali bus. I have fitted transporterhause horseshoe plates and down one outer spline. I haven't fitted any shocks yet as I need to do some measuring. My question is; how much clearance do you need between the drive...