Search results

Thanks for the reply il need to run a new wire to the dash. i had the dash out but theres alot of wires and connections there. You wouldn't be able to tell me where the wire should connect to once iv ran a new one.

Just trying to get my fuel gauge working. i have found that the 2 wires coming from the sender on the tank 1 is an earth the other has been cut for some reason by the previous owner. could anyone tell me where this should be going it is coming out heading towards the battery.

Nearly finished my restoration just the interior left to go in. We now have the interior sanded down, repaired if needed and revarnished all lying in the garage ready to go. Anyone have any useful tips on where to start and how long it should take to put it all in.

Need help I have renewed the discs pads and calipers on the front and new drums and shoes fitted on the rear. I have also put a new master cylinder on and took off the compensator valve split it and cleaned it. All new brake pipes and flexi pipes fitted new dot 4 brake fluid bleed the system but...

Looking for an indicator switch does anyone have one for sale. It's a 7 wire switch I am looking for.

I'm not sure how many wires I didn't think it would be that expensive. But I'm going to take it off and see if it's repairable first before I order one. I was looking at just the arm on gsf car parts but not sure if it's the correct part.

I have a faulty indicator switch on my 1971 bay. Anyone have one for sale or tell me where's the best place to source one.

Im going to have a go at making these and il see how a get on thanks again. Regards

Thanks for you info could you send me a picture of these L-shaped brackets please and i could make them. Thanks

I have managed to purchase 2 original cab seats to go in our camper. We removed the non original not long after we started our restoration. There are no brackets with the seats and after a little research I am no further forward as to how the seats are integrated. Can anyone point me in the...

Yes shes a devon i was thinking that another person would be a good idea. I will give it a try thanks for the help.

Just fitted my new roof and canvas can anyone tell me the best way to put the roof springs back on. when i took them off i took the screws out the plate which holds the box sections in the v position. They came off under alot of pressure and shot off down towards the floor.

Any know where I can get a set of new bumpers for my bus. I was thinking white ones but looks like there hard to come bye and might be forced to fit chrome ones.

Can anyone tell me the the ride height for my vw. I just finished putting the running gear back on my project but she looks very low at the back. I then lowered the torsion bar 1 notch which has helped the look but just wondered what size am looking for between the hub nut and the bottom of the...

Adjusted the brake shows so they were just touching and no more rebled the system again and brake pedal is becoming better. Because I'm used to modern vehicles and I bought the camper as a project I don't really know how the pedal should feel. Should it be similar or the same as a modern car or...

I will give your sugestions a try over the weekend when the fluid is coming out its solid no trace of air bubbles. Thanks for your help mate.

Done the pump test tonight for about 10 pumps each time the pedal just continues to be soft and carries on down to the floor. On the master cylinder there looks like a bolt in it on the top is this a bleed screw or has this got anything to do with my problem.

I have brake shoes on the back and disks on the front and i have tried adjusting the rear shoes. The system seems to be working as i can turn all 4 corners using my hands with no pressure on the pedal but when the mate puts pressure on the pedal all 4 corners lock solid. But pedal is soft for...

I purchased one of those eezybleed kits and tried again tonight. They work good I have brake fluid at each bleed nipple and at the master cylinder slowly I'm gettin a brake pedal but just not perfect. I'm now thinking the problem must be the master cylinder the camper has lay outside for 3 years...

We tried that aswell but no joy