Search results

Early Bay Forum

Help Support Early Bay Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. V

    Early Bay beam, RHD arm, drum spindles

    Looks like its had new BJ's relatively recently as they're pretty clean and not perished. Drums look in good condition. Small repairs done to the lower end box sections. Backing plates thrown out as rusted. Brake internals re-used so not available. So basically spindle to spindle with good...
  2. V

    Bell housing tinware

    £10 posted as is. Can get blasted & powder coated at cost. Not sure what year these are off. £15
  3. V

    Black laminated interior woodwork pieces.

    Need two pieces of the laminated wood, (black one side, slight patterned white other side). 285mm x 305mm 285mm x 245mm or larger to trim down, what have you got?
  4. V

    215mm Pressure Plate & friction disk, Spring plates etc.

    Used 215mm pressure plate & friction disc. German made. £20 Stock split bus spring plates. £30 Early bay (610mm long) rear torsion bars £20
  5. V

    Stainless steel exhaust.

    Heritage exhaust system http://www.vwheritage.com/vw_act_shop.product_pID_56919726_lang_EN_country_GB.htm" onclick="window.open(this.href);return false; Listed as £295 new. Came off an bus where the owner has gone stock. Two pre-heat bolts sheared off in the flange & tailpipe support bracket...
  6. V

    anyone run a stainless steel heritage exhaust?

    Morning, Anyone running one of these exhausts in their Bus? http://www.vwheritage.com/vw_act_shop.product_pID_56919726_lang_EN_country_GB.htm" onclick="window.open(this.href);return false; If so, ever had any problems with it or caused by it? I've pulled an engine out of a bay and the heads...
  7. V

    Just checking - clutch size on a 1600TP Bay

    On the assumption that the engine is completely as it left the factory in '76.... Would I be right in thinking; The T1 based engine = 1600cc The clutch is 215mm Thanks
  8. V

    Photo of Westy cupboards

    anyone got a photo of how the top rear locker cupboard on a full width westy is mounted? I've done a search, and all the vans that have the unit showing are 3/4 with side wardrobe which is different to the one that I'm fitting for a mate. cheers.
  9. V

    Wanted, hub carriers etc.

    Rear hub carriers, stub axles & hub nuts. Don't need brakes are driveshafts. What do you have available. Late bay is fine too.
  10. V

    So what do u lot do, when it comes 2 needing new brake drums

    Been working on an early Bay that had brake failure / crash.... :( Found that a previous owner has had the drums skimmed, but has gone MUCH further than the VW spec' for skimming brake drums. So these are toast and the bus has very poor brakes. BUT no one seems to stock them / all on back...
  11. V

    Late caliper mounting bolts

    Surplus to requirements. Never fitted, brand new.
  12. V

    Caliper mounting bolts don't fit...

    Fitting a new set of calipers / brakes etc. etc. and the bolts supplied in the kit are too large for the spindles. The spindles are meant to be 73- and that's what the bolts were supplied for. Any ideas? Thanks.
  13. V

    Sliding door needed

    Sliding door needed to fit on the LHS of a Bay. (RHD bus, sliding door on the left) Thanks.
  14. V

    Heater control pods & pipework

    Looking for the following. Got any off a van that's been modified? The metal duct that goes from the H/E to the heater control pod on the RHS of the van Both of the heater control pods that control the air flow Both of the flexible pipe sections that take the warm air into the van after the...
Top