Search results

Hi, can anyone recommend an engine builder in Cumbria or North of England?

Evening chaps, can anyone tell me if I can fit post '73 disc brakes up front and still run 14" steelies? Or will I need to go for 15" ones? cheers

My drivers mirror is a bit loose in its ball-joint and jumps about in the wind. Anyone got any tips for tightening it up?

Just got a pair of rear wheel bearing kits from Schofield's - the inner bearings are the same but the two outer ones look like two different types?? Rang Schofield's and they say they should both work... Anyone used both these types or is one wrong?

Got some raders for my bus :D To get them to fit under the rear arches I understand you can fit spacers on the rear to fit the hubs, but the hub nut still fouls the wheel and the center cap wont fit. I saw a post over on VZI talking about switching the rear stub axles for late ones (shorter)...

Just picked up a set of jge raders for my bus :D. When I hold them against a front hub they stick out a further 3cm(ish), the casting mark on the wheel says et+20. The plan is to go dropped spindles so I'm thinking I'll have to fit a narrowed beam? Before I go down this route can i ask is...

Need to replace the drivers side spindle on my LHD bus (is it known as left or right??) Anyone got one? Cheers

looking for this ...and the plastic cover that goes over it if possible?? :) cheers

Cylinder head tins, came off my US import Bay - a bit dirty but would clean up good *SOLD*

Following in the footsteps of AxlFoleys gearbox swap I have a query which someone might be able to help with... I am in the process of swapping the gearbox for a 1303s one, but the clutch release bearing in the '03s box is different to the old bus one (see below - the 1303s release bearing is...

my bus originally had the wheel mount on the front panel (now long gone) can anyone tell me if the bolt fixing holes will take a front badge or will i need to drill new ones? cheers

Getting my US import ready for its first UK MOT - horn not working :? Tested the horn - it does work, checked the live feed to it too, the problem is down to the earth wire connection at the bottom of the steering column, basically the ground wire coming from the horn stops there with a spade...

I'm looking for one of these... can anyone help? oops uploaded the wrong pic! This is the one I'm after:

Looking for the rear light backing plate which holds a single bulb. don't mind if a bit tatty but must have good connectors :)

I'm trying to replace the missing relays for my fusebox, but not sure if this IS the correct fusebox for my 1970 bay? I got a 2nd hand headlight relay (part #111941583) but the pin pattern doesn't seem to match up :roll: Can someone please have a quick look and possibly compare it with their...

I want to get new headlight and indicator relays for my 1970 US import bus, can anyone recommend a supplier? I've looked on various sites but they're a bit vague when it comes to pre 8/70 stuff. cheers Bob

All plus postage, some items might be best collected in person or by courier (from Carlisle) or I can price up postage if people are interested. Most bits came of my US import Bay so rust is superficial: Beetle over gearbox tinware (single-port) £10 Non-doghouse fan shroud – few dents but good...

I'm talking about the 10" early bay ones. There was a chap selling them on here back in 2008. Doesn't look like he's still on here :(

So here's the thing: on my bay I have one key for the ignition, another for the cab doors, no key for the sliding door and both the tailgate and engine door are push-button ones which I would like to convert to locking ones. I know I can buy separate locking handles for the sliding...

Been looking at Transporterhaus dropped spindles for the front of my bus and wondering how much I should drop the back end. Is anyone on here running their bommerang lowering plates? How easy is it to change a wheel? Piccies would be good :)