Fiiting Ply headliner?

[neil'69]

Hi all,

Can someone point out to me where the ply headliners clip into / how they stay in place?

Cheers

 

[Araon]

into the profiled ali trim pieces that run the length of the sides and across the roof

 

[rockandrollcamper]

into the profiled ali trim pieces that run the length of the sides and across the roof

Can you buy these ?

 

[vdub wannabe]

I have the same question.....where can you buy the it?

 

[Araon]

PM ego or grazy

 

[neil'69]

Hi all,

I'm looking at buying 1/2" aluminium angle, pop rivet it the length of the van, fit the ply then gently fold it over to hold the ply in place?

What do you think?

 

[Nick-Rackham]

May be better getting some U channel, and milling off almost one side so you have a nice clean edge all the way along, and a small lip to hold the ply? Just a thought!

EDIT, or something like this http://www.goodingalum.com/p9/prod83/Profiles/Panel-Wall-Board-Fixings/Pan-L-Trim/Panel-Wallboard-6mm-profiles/Pan-L-Trim:-Wallboard-Profiles" onclick="window.open(this.href);return false;

 

[Araon]

you can get the j channel and T pieces see above

 

[dubdubz]

ins't the roof ply 4mm? or is it 3mm? or none of the former!!

 

[flynster]

roof liner is 3mm
you can get the ali trim its a case of hunting it down....taken me ages but its all fun

ste

 

[EgoTrippin]

May be better getting some U channel, and milling off almost one side so you have a nice clean edge all the way along, and a small lip to hold the ply? Just a thought!

EDIT, or something like this http://www.goodingalum.com/p9/prod83/Profiles/Panel-Wall-Board-Fixings/Pan-L-Trim/Panel-Wallboard-6mm-profiles/Pan-L-Trim:-Wallboard-Profiles" onclick="window.open(this.href);return false;

The channels that Gooding Aluminium produce that are the closest match to Westy trims are these
http://www.goodingalum.com/p9/prod217/Profiles/Panel-Wall-Board-Fixings/Panel-Fix/Wall-Panel-Fixing-System" onclick="window.open(this.href);return false;
You need to use 1.5mm birch ply in 5' x 5' sheets to do this. These are the ones I used on mine.

 

[noddy]

Try these they do some profile that nearly identical to the og stuff (og was galvanized steel).
http://reimonew.ms-visucom.de/en/D-accessories/DW-conversion_parts_bits/DWJ-profiles_accessories/" onclick="window.open(this.href);return false;

 

[dubdubz]

Try these they do some profile that nearly identical to the og stuff (og was galvanized steel).
http://reimonew.ms-visucom.de/en/D-accessories/DW-conversion_parts_bits/DWJ-profiles_accessories/" onclick="window.open(this.href);return false;

which one theres lots on there........

 

[AxlFoley]

I would say this one

http://reimonew.ms-visucom.de/en/51210-alu_u_profile_254_cm/" onclick="window.open(this.href);return false;

looks spot on to me.

Mark

 

[stuk]

I couldn't find any channeling either the right profile or right finish anywhere, so I ended up using some tile edging strips from Topps Tiles. It comes in loads of different widths, lengths and finishes and it looks the dogs todgers if I say so myself.