Search results

A garage tidy up has turned up these bit's that are no longer needed. 4 spark plugs, 2 rocker cover gaskets, 1 belt (toothed - dynamo), 1 belt (solid - i think dynamo!). How's about the lot for a tenner posted? I think that's about half price...

Bought some of these brass bushes from Bugman, just in case, a couple of years back, but the bus didn't need them. The bus has since been sold and I have these in the garage unused, still in packet with instructions. They can be seen on Bugman's original thread here...

anyone know what the thread is on the bottom of the leg? cheers

I need 10 - 15 of the silver headed panel clips that fasten the sliding door and tailgate ply panels....... Pretty please ;)

Where does a westy interior light (the big one mounted near the side of the headliner) get it's live from and should it be permanent or switched - if so which switch. I seem to have no power to it, and i don't have a westy specific diagram. The Wire disapeares into the same loom that the cab...

NOW SOLD

SOLD_ SOLD _ SOLD

In need of 2 or 3 pretty please......... really don't want to have to use the black or pale grey JK ones - god knows why they don't have them colour matched to the originals!! Just the plastic fronts required, i don't need the latch part on the inside. Thanks

Firstly, furniture trim. I know the 'T' edge trim is available from Chewie baker on SSVC, but what about the other trim that goes around each door - is this available anywhere? Secondly, has anyone definitely sorted out replacement interior ply. The usual Birch ply that most people use doesn't...

Need the plastic trim around the long wardrobe door (the trim around the door itself, not the 'T' trim in the aperture). Must be perfect - no chips or cracks. Dropped mine today and chipped it in 2 places :roll: Or does anywhere repro this?

Anyone know off the top of your head what the size of the rear floor area is????

Don't know if this will be of any use to anyone - but if you're annoyed that your dipstick sender is way too long and needs bending to keep it away from your top pulley, they can be shortened..... Use a knife to prise open the connector block Remove the connectors by heating the solder...

What do you get? Just calculated mine after a 105 mile round trip...... and it's f@@***g terrible :shock: even allowing for the inaccuracy of the fuel guage (which magically started working last week!!! but still seems to run for miles on empty!) and that most of the trip was motorway at...

Bought from Machine 7 last month, now surplus to requirements. http://www.machine7.com/product.php?xProd=3262&xSec=1171" onclick="window.open(this.href);return false; I've had it out of the packet (and then put it back in) but it has never been used. It cost me £17.25 Yours for £11...

Good condition stock bottom pulley wanted - MUST be stamped with 'D'

Just cleaned mine up - decades of gunge :shock: What is the correct fill level of oil? there's no fill line or anything - but there is a sloping ridge thing about an inch up from the bottom, i've filled it to the bottom of this ridge, is this correct? Also the bottom of the air inlets isn't...

In need of a few bits for my 71, all must be in good condition Heater dash control levers - 2 red, 2 blue Illuminated hazard switch (or just the red vw/hazard insert would do) Dash brake warning light (or just the red lens) Off-side rear bumper splash pan I'm sure i'll think of other bits as...

Connected the heat exchangers up today - Never had a bus with working heaters before and got to say i'm impressed, it's chucking out much more heat than i expected. However i don't really know what the four lever controls do :oops: The coloured ends are missing too - so give me a run down left...

Picked up the 71 tintop from T2D yesterday :D Here's it getting it's final check over and then setting off back (photo's robbed from T2D blogs)