1967 Neptune Blue Deluxe

andrewblackwell · Sep 16, 2024

It just sparked my imagination.
I like how you have offset the arc at the stereo ends on your plate, rather than just squared off.

sparkywig · Sep 22, 2024

Just a couple of little jobs completed, but these took all day.....
First of all, steering column top insulating ring replaced.

Seat belt relocation brackets fitted.

12V socket installed.

And the door membranes done, with the extra pieces that go inside the inner door frame holes.

ozziedog · Sep 22, 2024

sparkywig said:
Just a couple of little jobs completed, but these took all day.....
First of all, steering column top insulating ring replaced.

View attachment 9529

View attachment 9530

Seat belt relocation brackets fitted.

View attachment 9532

12V socket installed.

View attachment 9533

And the door membranes done, with the extra pieces that go inside the inner door frame holes.

View attachment 9534

View attachment 9535

And that’s a great one to get done before winter hits us..

Ozziedog,,,,,,,,,need to check mine toooo

Wannabay · Sep 23, 2024

Where did you get the underdash 12V/USB socket from Sparky?

Albie5 · Sep 23, 2024

Tidy work !

sparkywig · Sep 23, 2024

Wannabay said:
Where did you get the underdash 12V/USB socket from Sparky?

I bought them from here

sparkywig · Oct 6, 2024

Diesel heater install.
Cut the perforated panel away from under the n/s seat, made a template for the holes required through the floor and drilled them out.

Inlet and exhaust installed and fuel line attached.

Fuel pump

Wiring connected and test run.

The outlet nozzle rotates, and I'll eventually fit a removable cover.
Just waiting on a bespoke diesel tank for the engine bay.

To get the heater under the seat base it can't be any wider or taller than 120mm.

Anybody need a 5kW diesel heater? It was sent by mistake and they won't accept returns.
Box only opened to measure heater body.

sparkywig · Oct 6, 2024

I also ran some speaker cables from the dash to the Westy bed base, but decided on a twin voice coil speaker for the original speaker position.

Unfortunately this meant the rev counter pod and wiring were in the way, so they had to be relocated. Had to drill two holes in the dash top that I wasn't too happy about, but never mind.
Speaker in and working. I added some foam seal around the edge of the speaker to wedge it under the dash edge trim and the bottom is held by two machine screws.
Quite impressed with the sound actually.

matty74 · Oct 8, 2024

Thanks

You inspired me to fix mine using the same method.

sparkywig · Oct 8, 2024

I think I've finally sorted the gearshift issues, hopefully.
Drilled another dimple in the rear shift rod about 5mm towards the gearbox, so effectively shortening the shift rod.
Goes into all gears, most especially reverse which was the issue.

While the front was up in the air, yet again, I remembered to grease the beam and spindles.

andrewblackwell · Oct 8, 2024

Did your moving the join position 5mm rearwards have the effect of pivoting your gearknob further forwards, such that the cup on the end of the shiftrod which the gearstick ball fits into has moved backwards off the front bush by 5mm too.
Or is it drawing the rear section of the shiftrod further forward slightly away from the gearbox nosecone?

sparkywig · Oct 8, 2024

It's pulling the rear shiftrod forward by 5mm. The front rod still touches the front bracket.

andrewblackwell · Oct 8, 2024

Thanks, that’s useful to know it helps with the shifting.

sparkywig · Oct 8, 2024

Don't forget I've got a non-stock shift rod and an engine/gearbox raise.

sparkywig · Oct 19, 2024

Today was spent butchering some ply, the Westy bed base to be exact.

Drop down door marked out. The bacon sandwich was very nice.

The router came out for the edge trim slot in the panel and door.

I bought some American cherry veneer a while back just for this.

Glued and clamped. Next job is trimming the veneer, a bit of oil to finish and then the edge trims can be glued on.

ozziedog · Oct 19, 2024

Ozziedog,,,,,,,,, looks great mate

Ben72Bay · Oct 19, 2024

sparkywig said:
Today was spent butchering some ply, the Westy bed base to be exact.

View attachment 9757

Drop down door marked out. The bacon sandwich was very nice.

View attachment 9752 View attachment 9753

The router came out for the edge trim slot in the panel and door.

View attachment 9754

I bought some American cherry veneer a while back just for this.

View attachment 9755 View attachment 9756

Glued and clamped. Next job is trimming the veneer, a bit of oil to finish and then the edge trims can be glued on.

View attachment 9758

That’s a lovely job!

sparkywig · Oct 25, 2024

I've got a couple of issues with the veneer, unfortunately it's lifted in a few places.
After seeking advice from a joiner friend it appears that dampness has caused the veneer to swell making it lift in places.
He did say that he uses a vacuum cabinet in a heated workshop to stop this happening, most helpful.
Anyway, out with a warm iron and a roller to see if that remedies the problem.

It does seem to be helping. More to follow.....

sparkywig · Oct 26, 2024

Well, that seems to have worked.
Sanded and a couple of coats of oil.

Hinges, handle and trim to be fitted now.
Follow along for the next instalment.

sparkywig · Thursday at 3:51 PM

Well, it's glued in place but that was an absolute ball ache. The trim comes packaged the wrong way to how it's fitted. And I have a strong love/hate relationship with contact adhesive.
I managed to get it fairly warm and pliable before fitting, so just hoping that it stays in place.

The good news is that my measuring was spot on and the door actually fits quite snugly in the opening.

1967 Neptune Blue Deluxe

Help Support Early Bay Forum:

Well-known member

Administrator

Well-known member

Well-known member

Well-known member

Administrator

Administrator

Administrator

Well-known member

Administrator

Well-known member

Administrator

Well-known member

Administrator

Administrator

Well-known member

Well-known member

Administrator

Administrator

Administrator

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!